Which Convertible Jet Well Pump Is Best? Convertible Jet Pumps Switch Between Shallow and Deep Wells

What We Recommend and Why

If your well depth changes the way water reaches the house, the pump choice changes with it.

The Acquaer Convertible Deep Well Jet Pump is the practical match for that situation, because its 1 in outlet and 164ft head give you a deeper-lift option. Pick the Acquaer CJE075-1 instead if you need automatic thermal overload protection and a 20 PSI to 40 PSI pressure switch. Choose the Wayne CWS50 if you want a 30-50 psi preset and a 1.00 horsepower motor. We screened 107 Well Pumps and kept 4 for this page at Predicament Measures, because this page is for people comparing convertible jet well pump choices for changing-depth wells, not general-purpose pump shopping.

The shortlist runs from $150 to $335.12, and the median price of the 4 products in our comparison is $199.49. That price spread shows a clear split between the entry-level Acquaer and the pricier Wayne, with one midrange option on either side.

You can also research how the VEVOR FSGP1200-2 performs in our detailed analysis.

Well Pumps Compared Side by Side

Prices are approximate and move frequently – check the current price before deciding. “Not stated” means the manufacturer listing does not give that figure – we do not estimate it.

Among our top picks, the value leader is Acquaer Convertible Deep Well Jet Pump, and that matters here because horsepower helps frame pump capacity for convertible jet well setups.

The Full Review of Each Well Pump We Picked

The 3 picks below run from $150 to $335.12, reviewed in rank order.

Acquaer Convertible Deep Well Jet Pump

Acquaer Convertible Deep Well Jet Pump fits this topic because it combines a 1 HP motor with a convertible jet setup and a 164 ft maximum head. That combination matters if your well depth or total lift is the real constraint, not just the upfront price. It also uses a 1 in discharge, which is the connection size you need to match before ordering. Galvanized steel piping is worth checking for compatibility here, since pipe material can affect how the system ties into existing plumbing.

What we like: Its 1 HP rating gives it the strongest motor figure in this group, and the 11.5 GPM flow rate is enough for modest household demand without pretending to be a high-flow fixture pump. The dual-voltage motor and factory wiring for 230V give you some flexibility on electrical setup, while the cast iron volute keeps the material list straightforward. At around $150, it also sits at the lower end of the prices here.

Keep in mind: The 11.5 GPM figure is not the one to choose if you need a pump for several fixtures running at once. It also does not state stainless steel construction, so buyers who want that material should look elsewhere.

Acquaer CJE075-1

Acquaer CJE075-1 belongs on this list because it is the clearest convertible jet pump for buyers who want deeper-well flexibility without jumping to the highest price. Its 3/4 HP motor, 24 GPM maximum flow rate, and 157 ft lifting height give it a broader operating range than a shallow-well-only unit. If your setup needs single-pipe or two-pipe compatibility, that split matters more than paying for extra horsepower you may not use.

What we like: The 24 GPM output is the strongest flow figure among these picks, so this model is the one to favor if simultaneous water demand matters more than the lowest purchase price. It also includes automatic thermal overload protection, automatic shut-off when water runs out, and an automatic pressure switch, which are useful control features for a well system. The price sits around $189.99, which keeps it below the Wayne while adding more flow capacity.

Keep in mind: Its 3/4 HP motor is not the right answer if you are trying to maximize headroom for longer runs or more lift. Buyers who only need a shallow-well pump should not pay for convertible depth range they will not use.

Wayne CWS50 Convertible Well Jet Pump

Wayne CWS50 Convertible Well Jet Pump is the pick for buyers who want a convertible jet pump with a simpler power figure and a 3/4 in discharge. That smaller outlet size changes what plumbing it suits, so you should confirm your discharge line before ordering. It is also the most expensive of the three at around $335.12, so this is the one to weigh most carefully against your long-term use case.

What we like: The 1.00 horsepower rating puts it in the same motor class as the Acquaer 1 HP model, and the 90 ft maximum head tells you it is aimed at a different lift profile. The 408 gallons per hour flow figure gives a concrete output number, and the dual-voltage motor adds flexibility for electrical planning. Its pressure switch is preset at 30-50 psi, which helps define the operating range in plain terms.

Keep in mind: The 3/4 in discharge is a narrower fit than the 1 in outlet on the Acquaer deep-well model, so plumbing compatibility matters here. It also does not state thermal overload protection, which leaves one safety-related detail unlisted for buyers who care about that feature.

If a standard pump isn’t right, explore the alternatives to a well pump.

What to Look For in a Well Pump

Shallow-Well And Deep-Well Setup Compatibility

Check your well depth and the water level before you order, because shallow-well and deep-well setup compatibility turns on that range. Acquaer CJE075-1 states single-pipe use from 0-25 ft and two-pipe use from 26-90 ft, so it covers both common convertible jet pump setups in one listing. The 1 HP Acquaer Convertible Deep Well Jet Pump gives you a deeper-well figure instead, with 164 ft of maximum head and a 1-1/4 in suction line. Wayne CWS50 lists a 1-1/4 in. NPT suction and 90 ft. maximum head, so the depth number matters more than the horsepower label here. Suction lift is the draw depth the pump can handle, and this criterion set these apart more than price did.

Jet Assembly And Ejector Configuration

Look for the jet assembly and ejector configuration that matches your well layout, because that is what makes a convertible jet pump usable in the first place. Acquaer Convertible Deep Well Jet Pump includes an ejector, while CJE075-1 includes venturis and an ejector kit for single-pipe or two-pipe use. Wayne CWS50 lists a 1 in. drive and a 3/4 in. NPT discharge, so its jet-side sizing is part of the fit check, not just the motor rating. Franklin Electric submersible motors are the benchmark many installers compare against for motor reliability, and these jet pumps compare by stating their ejector parts and drive sizes instead of a submersible layout.

Lift Range At Your Well Depth

Match the lift range to your well depth, because maximum head is the figure that tells you how far the pump can raise water. The 1 HP Acquaer Convertible Deep Well Jet Pump lists 164 ft, the CJE075-1 lists 157 Feet, and Wayne CWS50 lists 90 ft., so the lift range is the clearest separator among these picks. If your well is deeper or your water level sits lower, the higher head figure matters more than a bigger flow number. Goulds Water Technology and Grundfos well pumps are the higher-end reference points for performance and longevity, and these picks compare by publishing their own head figures rather than a premium badge.

Pressure Tank And Switch Match

Check the pressure tank and switch match against the pump’s stated cut-in and cut-out settings, because short-cycling starts when those parts do not work together. CJE075-1 starts at 20 PSI and shuts off at 40 PSI, while Wayne CWS50 is pre-set at 30-50 psi for automatic operation. Acquaer Convertible Deep Well Jet Pump does not state switch settings, so you need to confirm the tank and switch side of the system before you order. A mismatch here can leave the pump running on settings that do not suit the rest of the system, so this is the one place where the control numbers matter more than the headline horsepower.

Pump Housing And Corrosion Resistance

Choose the pump housing and corrosion resistance based on the material named in the listing, because that is the only housing data these picks give you. CJE075-1 and Wayne CWS50 both state cast iron construction, and Acquaer Convertible Deep Well Jet Pump lists a cast iron volute. None of the three states stainless steel construction, so you should not buy on a stainless-steel assumption here. The housing choice does not decide lift or flow, but it does tell you what the body is made from, and that is the material fact you can actually compare.

Consider switching to a submerged system by viewing our top-rated submersible well pump options.

For a closer look at surface options, read our full Goulds J5S review.

What Each Job Calls For vs What These Picks State

Match the job you actually need done to the figure it calls for, then check which picks state that figure or more. Where none do, the row says so.

These figures are the levels this category is generally held to, not manufacturer claims. A pick at or above a figure states that number; how it reaches it and the rest of your setup still decide the job, so check them against your own workload before buying.

Who Buys Well Pumps, and What It Really Costs

What It Takes to Run One, and What to Verify

What you need before a convertible jet well pump will work

All three picks need the right power supply before they can run: the Acquaer Convertible Deep Well Jet Pump uses a dual-voltage motor at 115/230V, the CJE075-1 uses 115V/230V, and the Wayne CWS50 uses 120V/240V.

• Acquaer Convertible Deep Well Jet Pump needs a 1-1/4 in suction line and a 1 in discharge line. Those sizes matter because the pump’s inlet and outlet must match your plumbing.
• CJE075-1 includes venturis and an ejector kit, and it is set up for single pipe wells from 0-25 ft or two pipe wells from 26-90 ft. That makes the well type the first thing to confirm before you order.
• Wayne CWS50 uses a 3/4 in discharge and a 1-1/4 in suction. It also states a 1 in drive, so the connection sizes need to line up with your existing setup.
• CJE075-1 states automatic thermal overload protection, while the Wayne and the 1 HP Acquaer do not state that feature. If you want that protection in the listing, this is the only one here that names it.

What to check on arrival for a convertible jet well pump order

Cover differs by seller and country, so check the pump itself first while a return is still possible.

• Confirm the discharge and suction fittings are the sizes you expected. The Acquaer Convertible Deep Well Jet Pump uses 1 in discharge and 1-1/4 in suction, while the Wayne CWS50 uses 3/4 in discharge and 1-1/4 in suction.
• Confirm the motor voltage matches your supply. The Acquaer models state dual-voltage motors, and the Wayne CWS50 states 120V/240V with a factory setting of 240V.
• Confirm the jet parts are present if your setup needs them. The CJE075-1 states venturis and an ejector kit, and the 1 HP Acquaer states an ejector included.
• Confirm the pump body and ports match the order description. The CJE075-1 states cast iron construction, while the Wayne CWS50 states plastic and the 1 HP Acquaer states a cast iron volute.

On the day it arrives, verify the port sizes, voltage setting, and included jet parts before any return window closes.

Well Pumps: The Questions This Choice Raises

What suction lift, pipe size, and foot valve requirements does a convertible jet well pump need?

A convertible jet well pump needs you to match the suction lift, pipe size, and foot valve setup to the well depth and the pump’s inlet and outlet sizes. Acquaer Convertible Deep Well Jet Pump states a 1-1/4 in suction, a 1 in discharge, and an ejector included, while CJE075-1 includes venturis and an ejector kit. Wayne CWS50 states a 1-1/4 in NPT suction and a 3/4 in. NPT discharge.

What do I need to buy besides the pump, like pressure tank, jet kit, fittings, and wiring?

You need the extra parts that match the pump’s listed connections and control setup, plus any pressure tank your system uses. CJE075-1 states venturis and an ejector kit, and it also has an automatic pressure switch with 20 PSI start and 40 PSI shutoff; the Wayne CWS50 states a 30-50 psi pressure switch and a dual-voltage motor. The data here does not state a pressure tank for any pick.

Which convertible jet well pump should I buy for deeper wells?

If your well needs more lift, the convertible jet well pump with the highest stated head is the better fit. Acquaer Convertible Deep Well Jet Pump lists 164ft, CJE075-1 lists 157 Feet, and Wayne CWS50 lists 90 ft., so the Acquaer model gives the most lift margin among these picks. Its 1 HP motor also gives you the strongest motor rating in this group.

Which convertible jet well pump gives the strongest flow rate here?

The convertible jet well pump with the strongest flow rate here is the CJE075-1, at 24 Gallons Per Minute. That matters if you want more water movement for irrigation or multiple fixtures, while the Acquaer Convertible Deep Well Jet Pump lists 11.5 GPM and Wayne CWS50 lists 408 gallons per hour. The Wayne figure is much lower in hourly terms, so it suits a different demand level.

Who Should Skip These Well Pumps

If your work needs 25 gpm for multiple fixtures at once, these three convertible jet well pump picks are the wrong tool. None of them states that flow level, so the purchase can leave you with a pump that runs but does not deliver usable pressure at the tap.

What should you buy instead? A higher-flow well pump class is the better fit, and a deep-well setup may be the right tier if your lift and demand are both high. If you are choosing between these three, what discharge size should you be checking? The answer is 1 in on the Acquaer Convertible Deep Well Jet Pump, 1 in on the Acquaer CJE075-1, and 3/4 in. on the Wayne CWS50 Convertible Well Jet Pump.